+90 850 549 98 38  ·  info@cybeletile.com

Technical

Product standard, test values, finishes, slip-resistance classes, thicknesses and general installation guidance.

Product standard and test values

Cybele Tile porcelain tiles are produced as dry-pressed porcelain tiles to TS EN 14411 Annex G, Group BIa; they are CE-marked and TSE-certified.

PropertyTest standardRequirementDeclared value
Product classTS EN 14411 Annex GGroup BIa (GL)Dry-pressed porcelain tile
Water absorptionTS EN ISO 10545-3E ≤ 0.5%0.15% (average)
Breaking strength (S)TS EN ISO 10545-4≥ 1300 N (≥ 7.5 mm) · ≥ 700 N (< 7.5 mm)2953 N (average)*
Modulus of rupture (R)TS EN ISO 10545-4≥ 35 N/mm²47.4 N/mm² (average)*
Reaction to fire96/603/EC—A1FL (without testing)
Frost resistanceTS EN ISO 10545-12RequiredResistant
Slip resistanceDIN 51130 / DIN 51097—R9–R13 · A/B/C (on request)
Release of dangerous substancesTS EN ISO 10545-15—Pb < 0.1% · Cd < 0.02%

* Test values measured on a 600×1200 mm, 9 mm sample; values may vary with thickness and size. Images are indicative; shade and pattern variation between faces is a natural characteristic of the product.

Finishes

Full Lappato

Fully polished surface with high light reflection that brings out the depth of colour and veining.

Lappato

Semi-polished: the surface is partially polished, combining a natural look with a soft sheen.

Satin matt

Silky, soft-touch matt surface with a gentle glow; easy to clean.

Matt

Natural, non-reflective surface; hides marks and offers safe use on floors.

Sugar Effect

A lightly textured surface that sparkles in the light thanks to fine crystal grains.

Metallic

A metallic sheen that shifts in tone with the light.

Full Body

Colour and pattern run through the whole body; appearance does not change with wear.

Slip-resistance classes

DIN 51130 — shod areas (angle of inclination)

  • R96°–10°
  • R1010°–19°
  • R1119°–27°
  • R1227°–35°
  • R13> 35°

DIN 51097 — barefoot wet areas

  • A≥ 12°
  • B≥ 18°
  • C≥ 24°

Typical use

  • R9Dry interiors
  • R10Entrances, kitchens
  • R11Outdoor, ramps
  • R12–R13Industrial areas
  • A/B/CShowers, pool surrounds

Slip resistance is developed on request; please specify your project requirement when enquiring.

Thickness · Size
  • 5 mmSlim: light, thin application; walls and façades
  • 8 · 9 mmFloors and walls
  • 14 mmAcid-resistant technical tile
  • 20 mmOutdoor floors
Available sizes (cm)
30×60
45×45
60×60
60×120
80×80
90×90
120×120
80×160

Every product in the collection can be produced in these sizes and finishes, independent of its catalogue size. Contact us with your project requirements.

General installation and care guidance

This guidance is general. Please consult our technical team for project-specific details.

Installation

  • The substrate must be flat, clean, dry and load-bearing; flatness is especially important for large formats.
  • For large-format and slim tiles use a high-performance, deformable cementitious adhesive, applied to both substrate and tile back for full coverage.
  • Tile levelling systems help prevent lippage on large formats.
  • Leave joints even with rectified tiles, and provide movement joints across large areas and at perimeters.
  • Dry-lay tiles from several boxes before installation to see the distribution of faces.

Cleaning and care

  • After installation, remove cement and grout residues with a suitable grout-residue cleaner.
  • Neutral detergent and water are sufficient for routine cleaning.
  • Do not use abrasive pads or powders on full lappato (polished) surfaces.
  • Products containing hydrofluoric acid damage porcelain surfaces and must not be used.