Technical
Product standard, test values, finishes, slip-resistance classes, thicknesses and general installation guidance.
Product standard and test values
Cybele Tile porcelain tiles are produced as dry-pressed porcelain tiles to TS EN 14411 Annex G, Group BIa; they are CE-marked and TSE-certified.
| Property | Test standard | Requirement | Declared value |
|---|---|---|---|
| Product class | TS EN 14411 Annex G | Group BIa (GL) | Dry-pressed porcelain tile |
| Water absorption | TS EN ISO 10545-3 | E ≤ 0.5% | 0.15% (average) |
| Breaking strength (S) | TS EN ISO 10545-4 | ≥ 1300 N (≥ 7.5 mm) · ≥ 700 N (< 7.5 mm) | 2953 N (average)* |
| Modulus of rupture (R) | TS EN ISO 10545-4 | ≥ 35 N/mm² | 47.4 N/mm² (average)* |
| Reaction to fire | 96/603/EC | — | A1FL (without testing) |
| Frost resistance | TS EN ISO 10545-12 | Required | Resistant |
| Slip resistance | DIN 51130 / DIN 51097 | — | R9–R13 · A/B/C (on request) |
| Release of dangerous substances | TS EN ISO 10545-15 | — | Pb < 0.1% · Cd < 0.02% |
* Test values measured on a 600×1200 mm, 9 mm sample; values may vary with thickness and size. Images are indicative; shade and pattern variation between faces is a natural characteristic of the product.
Finishes
Full Lappato
Fully polished surface with high light reflection that brings out the depth of colour and veining.
Lappato
Semi-polished: the surface is partially polished, combining a natural look with a soft sheen.
Satin matt
Silky, soft-touch matt surface with a gentle glow; easy to clean.
Matt
Natural, non-reflective surface; hides marks and offers safe use on floors.
Sugar Effect
A lightly textured surface that sparkles in the light thanks to fine crystal grains.
Metallic
A metallic sheen that shifts in tone with the light.
Full Body
Colour and pattern run through the whole body; appearance does not change with wear.
Slip-resistance classes
DIN 51130 — shod areas (angle of inclination)
- R96°–10°
- R1010°–19°
- R1119°–27°
- R1227°–35°
- R13> 35°
DIN 51097 — barefoot wet areas
- A≥ 12°
- B≥ 18°
- C≥ 24°
Typical use
- R9Dry interiors
- R10Entrances, kitchens
- R11Outdoor, ramps
- R12–R13Industrial areas
- A/B/CShowers, pool surrounds
Slip resistance is developed on request; please specify your project requirement when enquiring.
- 5 mmSlim: light, thin application; walls and façades
- 8 · 9 mmFloors and walls
- 14 mmAcid-resistant technical tile
- 20 mmOutdoor floors
Every product in the collection can be produced in these sizes and finishes, independent of its catalogue size. Contact us with your project requirements.
General installation and care guidance
This guidance is general. Please consult our technical team for project-specific details.
Installation
- The substrate must be flat, clean, dry and load-bearing; flatness is especially important for large formats.
- For large-format and slim tiles use a high-performance, deformable cementitious adhesive, applied to both substrate and tile back for full coverage.
- Tile levelling systems help prevent lippage on large formats.
- Leave joints even with rectified tiles, and provide movement joints across large areas and at perimeters.
- Dry-lay tiles from several boxes before installation to see the distribution of faces.
Cleaning and care
- After installation, remove cement and grout residues with a suitable grout-residue cleaner.
- Neutral detergent and water are sufficient for routine cleaning.
- Do not use abrasive pads or powders on full lappato (polished) surfaces.
- Products containing hydrofluoric acid damage porcelain surfaces and must not be used.